1/4 rev. a structure silicon monolithic integrated circuits product series bipolar stepping motor driver type bd63875efv function ? pwm constant current controllable two h bridge driver ? built-in translator circuit for clk-in control ? full, half, and quarter step modes ? mix decay control absolute maximu m ratings(ta=25 ) item symbol limit unit supply voltage v cc1,2 -0.2 +36.0 v power dissipation pd 1.45 1 w 4.70 2 w input voltage for control pin v in -0.2 +5.5 v rnf maximum voltage v rnf 0.7 v maximum output current i out 1.5 3 a/phase maximum output current(peak) 4 i outpeak 2.0 3 a/phase operating temperature range t opr -25 +85 storage temperature range t stg -55 +150 junction temperature t jmax +150 1 70mm 70mm 1.6mm glass epoxy board. derating in done at 11.6mw/ for operating above ta=25 . 2 4-layer recommended board. derating in done at 37.6mw/ for operating above ta=25 . 3 do not, however exceed pd, aso and tjmax=150 . 4 pulse width tw Q 1ms, duty 20%. recommended operating conditions (ta=-25 +85 ) item symbol min. typ. max. unit supply voltage v cc1,2 19 24 28 v output current i out - 1.0 1.2 5 a/phase 5 do not, however exceed pd, aso. this product isn?t designed for protection against radioactive rays. .
2/4 rev. a electrical characteristics (unless otherwise specified, ta=25 , v cc1,2 =24v) item symbol limit unit conditions min. typ. max. whole circuit current at standby i ccst - 1.0 2.5 ma ps=l circuit current i cc - 2.5 5.0 ma ps=h, vref=3v control input (clk, cw_ccw, mode0, mode1, enable, ps) h level input voltage v inh 2.0 - - v l level input voltage v inl - - 0.8 v h level input current i inh 35 50 100 a v in =5v l level input current i inl -10 0 - a v in =0v output (out1a, out1b, out2a, out2b) output on resistance r on - 1.0 1.3 i out =1.0a, sum of upper and lower output leak current i leak - - 10 a current control rnfxs input current i rnfs -2.0 -0.1 - a rnfxs=0v rnfx input current i rnf -40 -20 - a rnfx=0v vref input current i vref -2.0 -0.1 - a vref=0v vref input voltage range v ref 0 - 3.0 v mth input current i mth -2.0 -0.1 - a mth=0v mth input voltage range v mth 0 - 3.5 v comparator threshold v cth 0.57 0.60 0.63 v vref=3v minimum on time (blank time) t onmin 0.3 0.8 1.5 s c=1000pf, r=39k
3/4 rev. a package outline block diagram pin no. / pin name pin no. pin name pin no. pin name 1 gnd 15 clk 2 out1b 16 cw_ccw 3 rnf1 17 test 4 rnf1s 18 mode0 5 out1a 19 mode1 6 nc 20 enable 7 vcc1 21 nc 8 nc 22 vcc2 9 gnd 23 nc 10 cr 24 out2a 11 nc 25 rnf2s 12 mth 26 rnf2 13 vref 27 out2b 14 ps 28 nc nc : non connection lot no. product no. htssop-b28 (unit:mm) bd63875efv predriver 7 vcc1 blank time pwm control translator 2bit dac tsd uvlo regulator reset 9 gnd 10 cr 12 mth 14 ps 15 clk 18 mode0 19 mode1 16 cw_ccw 20 enable vref 13 2 out1b 5 out1a 3 rnf1 22 vcc2 24 out2a 1 gnd 27 out2b 26 rnf2 17 test control logic mix decay control ocp osc rnf1s 4 rnf2s 25 ovlo
4/4 rev. a operation notes (1) absolute maximum ratings an excess in the absolute maximum ratings, such as supply voltage, temper ature range of operating conditions, etc., can break down the devices, thus ma king impossible to identify breaking mode, such as a short circuit or an open circuit. if any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses. (2) power supply lines as return of current regenerated by back emf of mo tor happens, take steps such as putting capacitor between power supply and gnd as an electric pathway for the regenerated current. be sure that there is no problem with each property such as emptied capacity at lower temperature regarding electrolytic capacitor to decide capacity value. if the connected power supply does not have sufficient current absorption capacity, regenerative current will cause the voltage on the power supply line to rise, which combined with the product and its peripheral circuitry may exceed the absolute maximum ratings. it is recommended to implement a physical safety measure such as the in sertion of a voltage clamp diode between the power supply and gnd pins. (3) gnd potential the potential of gnd pin must be minimu m potential in all operating conditions. (4) metal on the backside (define the side wher e product markings are printed as front) the metal on the backside is shorted wi th the backside of ic chip therefor e it should be c onnected to gnd. be aware that there is a possibility of malfunction or destruction if it is shorted with any potential other than gnd. (5) thermal design use a thermal design that allows for a sufficient margin in light of the power dissipation (pd) in actual operating conditions. this ic exposes its frame of the backside of package. note that this part is assumed to use after providing heat dissipation treatment to improve heat dissipation efficiency . try to occupy as wide as possible with heat dissipation pattern not only on the board surface but also the backside. (6) actions in strong electromagnetic field use caution when using the ic in t he presence of a strong electromagnet ic field as doing so may cause the ic to malfunction. (7) aso when using the ic, set the output transistor so that it does not exceed absolute maximum ratings or aso. (8) thermal shutdown circuit the ic has a built-in thermal shutdown circuit (tsd circuit). if the chip temperature becomes tjmax=150 , and higher, coil output to the motor will be open. the tsd circuit is designed only to shut the ic off to prevent runaway thermal operation. it is not designed to protect or indemnify peripheral equipment. do not use the tsd function to protect peripheral equipment. (9) ground wiring pattern when using both large current and small signal gnd pa tterns, it is recommended to isolate the two ground patterns, placing a single ground poi nt at the ground potent ial of application so that the pattern wiring resistance and voltage variations caused by large currents do not cause variations in the small signal ground voltage. be careful not to change the gnd wiring pattern of any external components, either. (10) test pin be sure to connect test pin to gnd.
r1010 a www.rohm.com ? 2010 rohm co., ltd. all rights reserved. notice rohm customer support system http://www.rohm.com/contact/ thank you for your accessing to rohm product informations. more detail product informations and catalogs are available, please contact us. notes no copying or reproduction of this document, in part or in whole, is permitted without the consent of rohm co.,ltd. the content specied herein is subject to change for improvement without notice. the content specied herein is for the purpose of introducing rohm's products (hereinafter "products"). if you wish to use any such product, please be sure to refer to the specications, which can be obtained from rohm upon request. examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the products. the peripheral conditions must be taken into account when designing circuits for mass production. great care was taken in ensuring the accuracy of the information specied in this document. however, should you incur any damage arising from any inaccuracy or misprint of such information, rohm shall bear no responsibility for such damage. the technical information specied herein is intended only to show the typical functions of and examples of application circuits for the products. rohm does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by rohm and other parties. rohm shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. the products specied in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, ofce-automation equipment, commu- nication devices, electronic appliances and amusement devices). the products specied in this document are not designed to be radiation tolerant. while rohm always makes efforts to enhance the quality and reliability of its products, a product may fail or malfunction for a variety of reasons. please be sure to implement in your equipment using the products safety measures to guard against the possibility of physical injury, re or any other damage caused in the event of the failure of any product, such as derating, redunda ncy, re control and fail-safe designs. rohm shall bear no responsibility whatsoever for your use of any product outside of the prescribed scope or not in accordance with the instruction manual. the products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospac e machinery, nuclear-reactor controller, fuel- controller or other safety device). rohm shall bear no responsibility in any way for use of any of the products for the above special purposes. if a product is intended to be used for any such special purpose, please contact a rohm sales representative before purchasing. if you intend to export or ship overseas any product or technology specied herein that may be controlled under the foreign exchange and the foreign trade law, you will be required to obtain a license or permit under the law.
|
